Few door parts needed to finish

Place to put want ads for FSJ parts
Forum rules
Please read the sales area rules before posting here. Thanks!
Post Reply

Topic author
wainwright
Posts: 2
Joined: Wed Jul 25, 2018 3:47 am

Few door parts needed to finish

Post by wainwright » Fri May 22, 2020 4:05 am

At the end (yes!) of of a complete nut n bolt rebuild of 1989 GW.
Looking for the following small parts to finish:

Rear door armrest in sand
Clip insert in door that accepts armrest screw (2)
Rear door lower woodgrain strip (1)
Front door reflector armrest inserts (decent set a long shot, I know)
Round plugs over floor seatbelt bolts behind front seat (2) in sand

Thanks very much. Great forums that have helped me tremendously.
Wainwright


Dr.Bob
Posts: 66
Joined: Thu Dec 26, 2019 8:57 pm

Re: Few door parts needed to finish

Post by Dr.Bob » Fri May 22, 2020 6:26 am

I don't have any of those parts, but just want to point out that the clip that the armrest screws grab into should be an ordinary "spring nut" that you can buy at most hardware stores or auto-parts stores in the appropriate size for those screws:

https://www.lowes.com/pl/Spring-nuts-Nu ... 4294710807

User avatar

jsinajeep
Posts: 1842
Joined: Tue Aug 23, 2011 8:25 pm
Location: Globe AZ.

Re: Few door parts needed to finish

Post by jsinajeep » Fri May 22, 2020 7:31 pm

Dr.Bob wrote:
Fri May 22, 2020 6:26 am
I don't have any of those parts, but just want to point out that the clip that the armrest screws grab into should be an ordinary "spring nut" that you can buy at most hardware stores or auto-parts stores in the appropriate size for those screws:

https://www.lowes.com/pl/Spring-nuts-Nu ... 4294710807

Those clip are not even close.

User avatar

jsinajeep
Posts: 1842
Joined: Tue Aug 23, 2011 8:25 pm
Location: Globe AZ.

Re: Few door parts needed to finish

Post by jsinajeep » Fri May 22, 2020 7:32 pm

I should have the clips PM me


candymancan
Posts: 2678
Joined: Tue Mar 22, 2016 11:32 pm

Re: Few door parts needed to finish

Post by candymancan » Mon May 25, 2020 7:13 pm

You need the reflector inserts for the arm rests correct ? I have 1 or two in storage i dont need from a 89 or 90 doesnt matter theyre the same ,,Theyre not broken.. but the fake chrome is a bit worn out/blackish. Reflector is fine.

Lemme know if youre interested
1998 Jeep Grand Cherokee 5.9L Limited 197k
1998 Jeep Grand Cherokee 4.0 I6 laredo 299k
1990 Jeep Grand Wagoneer 138k


Topic author
wainwright
Posts: 2
Joined: Wed Jul 25, 2018 3:47 am

Re: Few door parts needed to finish

Post by wainwright » Wed May 27, 2020 5:24 pm

Thanks for the replies.
I do have two reflector inserts original to the vehicle, but they meet the same description as above: good reflector, but chipped or stripped chromed plastic surround revealing lots of black. Barring a good set being found, if anyone has a good method to restore the look of these (chrome tape, etc.) short of truly rechroming the plastic, do tell.
I'm still looking for the other parts not addressed in the above replies.
Thanks again to this forum.


candymancan
Posts: 2678
Joined: Tue Mar 22, 2016 11:32 pm

Re: Few door parts needed to finish

Post by candymancan » Sat May 30, 2020 11:21 pm

You provly wont find a good set... never seen them good. Your best bet would be to go to the hardware or autopart store.. get some chrome/reflective paint. Tape off the peice and paint it so itll be shiney again. Thats what id do
1998 Jeep Grand Cherokee 5.9L Limited 197k
1998 Jeep Grand Cherokee 4.0 I6 laredo 299k
1990 Jeep Grand Wagoneer 138k

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests