Page 6 of 8

Re: For all you fabricators out there I give you

Posted: Fri Jun 19, 2020 10:00 am
by bigun
Thank God LOL

Re: For all you fabricators out there I give you

Posted: Fri Jun 19, 2020 10:30 am
by will e
More engine work but again it is entertaining and the attention to detail is impressive as always. Richard says in the video something like "You can just bolt on aftermarket parts, you have to take a holistic approach".

Re: For all you fabricators out there I give you

Posted: Fri Jun 19, 2020 12:22 pm
by bigun
Like they said they could have had the whole thing built in a couple of months if they hadn't paid attention to all the details like electric windows, door locks, side impact stereo system, all the body work, seats, electrical... What is truly amazing is how far ahead they were thinking, grounding points welded in 5 years ago just being used now. Richard admitting he did the head work 2 years ago

Re: For all you fabricators out there I give you

Posted: Fri Jun 19, 2020 2:38 pm
by will e
No doubt. They thought a lot of things ahead (but also admit when they got caught off guard). It really is an amazing build. It' won't be 'the fastest' mini or even 'the best handling' but goodness, it is probably the coolest overall.

I do 'worry' about all of the electronics but Richard seems to be doing a proper job. Having the right crimping tools is key, especially with that many connectors.

Re: For all you fabricators out there I give you

Posted: Fri Jun 19, 2020 3:50 pm
by letank
will e wrote: Fri Jun 19, 2020 2:38 pm Having the right crimping tools is key, especially with that many connectors.
Agreed on the crimper, I bought a supposedly nice crimper... but it is worthless , i can pull the wires off, even with all the possibilities... OK it does spark plug wires!

Re: For all you fabricators out there I give you

Posted: Fri Jun 19, 2020 4:11 pm
by sirrus
x2 on importance of good crimper! I usually prefer ratcheting style crimpers as they require less force (I couldn't use some of my non-ratcheting ones after I had my hand injury) and usually get you a better crimp. Having properly shaped dies is also important.

Sometimes you can save a bad crimp by soldering it a bit, but gets old pretty quick if you have a lot of them.

Re: For all you fabricators out there I give you

Posted: Wed Jun 24, 2020 1:45 pm
by SlowGear
Wish I would have seen this thread when it started five years ago. I only recently "found" Project Binky. Pretty much binged 30 episodes in about a week (thanks Covid-19).
Have been sharing it with friends, warning them they better have their chores done because the boys from Shropshire will be taking all your time for a while;-)

Re: For all you fabricators out there I give you

Posted: Wed Jun 24, 2020 2:50 pm
by bigun
SlowGear wrote: Wed Jun 24, 2020 1:45 pm Wish I would have seen this thread when it started five years ago. I only recently "found" Project Binky. Pretty much binged 30 episodes in about a week (thanks Covid-19).
Have been sharing it with friends, warning them they better have their chores done because the boys from Shropshire will be taking all your time for a while;-)
Every once in a while I'll start back at the beginning just to marvel at how far the have come

Re: For all you fabricators out there I give you

Posted: Sun Jul 05, 2020 5:11 pm
by bigun
I don't know if I have posted this guy before
Mike Patey the airplane builder version of Bad Obsession except faster

https://www.youtube.com/watch?v=tqGnlFYAq1I

Re: For all you fabricators out there I give you

Posted: Thu Jan 28, 2021 12:18 pm
by will e
New episode tomorrow. As a Patreon donator I got to watch 24 hours in advance. You will not be disappointed. No spoilers....

Re: For all you fabricators out there I give you

Posted: Thu Jan 28, 2021 3:47 pm
by bigun
will e wrote: Thu Jan 28, 2021 12:18 pm New episode tomorrow. As a Patreon donator I got to watch 24 hours in advance. You will not be disappointed. No spoilers....
If you had spoiled it I would hunt you down and give you such a talking too! :-bd

Re: For all you fabricators out there I give you

Posted: Fri Jan 29, 2021 1:54 pm
by bigun
IT'S HERE IT'S HERE!!!!!!!!!
Will E was right! :D


https://www.youtube.com/watch?v=PE9UP2NbIVU

Re: For all you fabricators out there I give you

Posted: Fri Jan 29, 2021 11:50 pm
by sirrus
Finally! Absolutely amazing and I realized that I forgot what they were doing with the engine in the previous episodes. Good excuse to rewatch them ;)

Re: For all you fabricators out there I give you

Posted: Sat Jan 30, 2021 12:14 pm
by wimsurf
oh my, I think I just found a series that will cost me the rest of the weekend..

Re: For all you fabricators out there I give you

Posted: Sun Jan 31, 2021 5:04 pm
by will e
I rewatched episode 1 after watching the latest. So funny to see Binky in its beginning condition.

Re: For all you fabricators out there I give you

Posted: Sun Jan 31, 2021 6:11 pm
by bigun
wimsurf wrote: Sat Jan 30, 2021 12:14 pm oh my, I think I just found a series that will cost me the rest of the weekend..
After that go watch
Mike Patey's airplane builds you can hate me later LOL

https://www.youtube.com/channel/UCSvdee ... rloZjWwNVg

If your into boat building these guys started with living trees to build their boat

https://www.youtube.com/channel/UCAiDWn ... Cp6uuUo0VA

Re: For all you fabricators out there I give you

Posted: Sun Jan 31, 2021 6:13 pm
by bigun
will e wrote: Sun Jan 31, 2021 5:04 pm I rewatched episode 1 after watching the latest. So funny to see Binky in its beginning condition.
It's hard to believe it has been so long, but then look at what they have done! :shock:

Re: For all you fabricators out there I give you

Posted: Fri Feb 05, 2021 6:40 pm
by letank
the escargot is a hoot too.... it could have been cheaper to stay in local hotels and put blinky on a trailer...

https://www.youtube.com/watch?v=6HXSigszx5w

Re: For all you fabricators out there I give you

Posted: Fri Feb 05, 2021 9:29 pm
by bigun
letank wrote: Fri Feb 05, 2021 6:40 pm the escargot is a hoot too.... it could have been cheaper to stay in local hotels and put blinky on a trailer...

https://www.youtube.com/watch?v=6HXSigszx5w
Got me all excited thought they had added another video :( :(

Re: For all you fabricators out there I give you

Posted: Fri Feb 05, 2021 9:31 pm
by bigun