Right side ash tray

Place to put want ads for FSJ parts
Forum rules
Please read the sales area rules before posting here. Thanks!
Post Reply
User avatar

Topic author
devildog80
Posts: 1149
Joined: Wed Apr 13, 2022 2:41 pm
Location: Apache Junction AZ

Right side ash tray

Post by devildog80 »

Looking for a right side ash tray, as shown in pic below of an older J10. Barter/trade if anyone has one. I have a glove box door for an older rig, like the one below, green with some badge on it.
My '84 GW currently is Nutmeg color, only one ash tray per factory build, but will take any color. Removing the clock in mine, to install the ash tray.

Imageash tray by Scott Weckerly, on Flickr
'81 CJ5 Base, 258 I6, MC2100, T176 4 spd, 300 TC, D30 Front NT, 3.31, 2-Piece AMC 20 rear NT, 3.31, 4" high arc spring lift
'84 Grand Wagoneer, 401 V8 (.030 over), Edelbrock clone 1406, 727 auto, Selec-trac NP229, AMC 20 REAR - D44 FRONT - WT 3.31, 4" high arc spring lift
Rather be driving, than waiting to be modified
User avatar

Yeller
Posts: 1584
Joined: Thu Apr 01, 2021 7:54 am
Location: Rogers County Oklahoma

Re: Right side ash tray

Post by Yeller »

Need to look behind the clock and see if the sliders are in the dash to hold the tray, if it’s not there I’m not sure how you would install that without pulling the dash out, I think they are spot welded in.
The bus I ride is so short it is a yellow Smart Car full of squirrels, monkeys and clowns.

1970 J2500 Resto Mod
https://www.fsjnetwork.com/forum/viewt ... 12&t=21395

1974 Bronco “Broncno”
https://classicbroncos.com/forums/threa ... st-3411909
User avatar

Topic author
devildog80
Posts: 1149
Joined: Wed Apr 13, 2022 2:41 pm
Location: Apache Junction AZ

Re: Right side ash tray

Post by devildog80 »

My existing was a bit wonky when I got the truck, and found it was just screwed in, so figure the other side should do the same. Dash base probably has the mounting holes needed, but good idea to check. Will make it work either way, just need the complete tray, with mounting mechanism included. Also noticed the opposing upper left and right corners are rounded slightly, and not just a 90* angle, but again will modify to fit correctly as needed.
Thanks
'81 CJ5 Base, 258 I6, MC2100, T176 4 spd, 300 TC, D30 Front NT, 3.31, 2-Piece AMC 20 rear NT, 3.31, 4" high arc spring lift
'84 Grand Wagoneer, 401 V8 (.030 over), Edelbrock clone 1406, 727 auto, Selec-trac NP229, AMC 20 REAR - D44 FRONT - WT 3.31, 4" high arc spring lift
Rather be driving, than waiting to be modified

will e
Posts: 5105
Joined: Sat Aug 18, 2012 8:21 am

Re: Right side ash tray

Post by will e »

Two ashtrays and no cup holders. It was a different time!
81 Waggy 'WILL E' Retired
82 Cherokee WT - SOA/SF/high steer/Alcan springs/agr box/Borgeson steering shaft/AMC 401/performer/holley TA/HEI/BeCool/727/ALTAS (2.0/2.72/5.44)/D60 Snofighter(Yukon Zip,hubs,stubs,4.56)/14 Bolt (FF,BF shave, Discs, ARB,Artec Truss)/MTR 37X12.5/Corbeau XRS Baja & 5 point retractable harness/Hella Aux lights/tuffy console/killer32 sliders/Evil Twin bumpers, rack and roll cage/WARN 8000/TT Fabworks steering brace/dual batts/custom TC skid plate/ARB fridge
User avatar

Topic author
devildog80
Posts: 1149
Joined: Wed Apr 13, 2022 2:41 pm
Location: Apache Junction AZ

Re: Right side ash tray

Post by devildog80 »

So true. I am still running without my front door cards on, so have magnetic cup holders from O'Reillys on the doors right now. Thinking I could cut the door cards, when time for them to go back on, so the magnetic cup holders could continue to be utilized. Want to build a custom console to mount the CB radio, possibly a regular radio, cell phone holder, storage, and include cup holders there as well. Dash port for regular radio might make into cell phone slot with USB connection, just a little catch cubby for small notebook, maybe a switch panel for on board air I want to mount in the back, and other lighting or indicator lights for whatever else I add in later.
Fairly good building with wood, so will make a cardboard template for final design, then get it made. Need to do carpet and insulation first, so will be awhile, unless I win the lottery.
'81 CJ5 Base, 258 I6, MC2100, T176 4 spd, 300 TC, D30 Front NT, 3.31, 2-Piece AMC 20 rear NT, 3.31, 4" high arc spring lift
'84 Grand Wagoneer, 401 V8 (.030 over), Edelbrock clone 1406, 727 auto, Selec-trac NP229, AMC 20 REAR - D44 FRONT - WT 3.31, 4" high arc spring lift
Rather be driving, than waiting to be modified
User avatar

Topic author
devildog80
Posts: 1149
Joined: Wed Apr 13, 2022 2:41 pm
Location: Apache Junction AZ

Re: Right side ash tray

Post by devildog80 »

Have a matched tray from an IFSJA forum member who is sending soon. Will pull the clock out while waiting and see what framework of the dash looks like behind it.
'81 CJ5 Base, 258 I6, MC2100, T176 4 spd, 300 TC, D30 Front NT, 3.31, 2-Piece AMC 20 rear NT, 3.31, 4" high arc spring lift
'84 Grand Wagoneer, 401 V8 (.030 over), Edelbrock clone 1406, 727 auto, Selec-trac NP229, AMC 20 REAR - D44 FRONT - WT 3.31, 4" high arc spring lift
Rather be driving, than waiting to be modified
Post Reply