Thanks
Where to Connect?
-
HowardT64
Topic author - Posts: 1536
- Joined: Sun May 05, 2013 2:47 am
- Location: Athens,Texas
Where to Connect?
Okay...the reason my heater AND 4wd wont work....theres no Vacuum to operate either system. Currently they are plugged into the hose that goes to the PCV valve. I need to plug the Vac cannister for both, into a source that will make them work. Can anyone give me an idea where to plug it in?
Thanks
Thanks
2016 Jeep Patriot
"Faith"
"Faith"
-
HowardT64
Topic author - Posts: 1536
- Joined: Sun May 05, 2013 2:47 am
- Location: Athens,Texas
Re: Where to Connect?
Okay got a picture of the area...just need to know where on the manifold to plug it in
2016 Jeep Patriot
"Faith"
"Faith"
-
Stuka
- Site Admin
- Posts: 11804
- Joined: Thu May 12, 2011 5:53 pm
- Location: CA
- Contact:
Re: Where to Connect?
Anywhere that is manifold vacuum should work. Which is to say, a port on the manifold that doesn't have a CTO on it (The CTO turns the vacuum on and off).
2017 JKU Rubicon
Pevious Jeeps: 1981 J10, 1975 Cherokee, 2008 JK, 2005 KJ, 1989 XJ
Pevious Jeeps: 1981 J10, 1975 Cherokee, 2008 JK, 2005 KJ, 1989 XJ
-
will e
- Posts: 5103
- Joined: Sat Aug 18, 2012 8:21 am
Re: Where to Connect?
Like Stuka said. If you can't find an available port you can always add a 't' fitting.
If you post a picture of your intake manifold with the air cleaner off we can probably be more specific.
If you post a picture of your intake manifold with the air cleaner off we can probably be more specific.
81 Waggy 'WILL E' Retired
82 Cherokee WT - SOA/SF/high steer/Alcan springs/agr box/Borgeson steering shaft/AMC 401/performer/holley TA/HEI/BeCool/727/ALTAS (2.0/2.72/5.44)/D60 Snofighter(Yukon Zip,hubs,stubs,4.56)/14 Bolt (FF,BF shave, Discs, ARB,Artec Truss)/MTR 37X12.5/Corbeau XRS Baja & 5 point retractable harness/Hella Aux lights/tuffy console/killer32 sliders/Evil Twin bumpers, rack and roll cage/WARN 8000/TT Fabworks steering brace/dual batts/custom TC skid plate/ARB fridge
82 Cherokee WT - SOA/SF/high steer/Alcan springs/agr box/Borgeson steering shaft/AMC 401/performer/holley TA/HEI/BeCool/727/ALTAS (2.0/2.72/5.44)/D60 Snofighter(Yukon Zip,hubs,stubs,4.56)/14 Bolt (FF,BF shave, Discs, ARB,Artec Truss)/MTR 37X12.5/Corbeau XRS Baja & 5 point retractable harness/Hella Aux lights/tuffy console/killer32 sliders/Evil Twin bumpers, rack and roll cage/WARN 8000/TT Fabworks steering brace/dual batts/custom TC skid plate/ARB fridge
-
HowardT64
Topic author - Posts: 1536
- Joined: Sun May 05, 2013 2:47 am
- Location: Athens,Texas
Re: Where to Connect?
okay I will take a picture later...we almost have this nailed down
2016 Jeep Patriot
"Faith"
"Faith"
-
HowardT64
Topic author - Posts: 1536
- Joined: Sun May 05, 2013 2:47 am
- Location: Athens,Texas
Re: Where to Connect?
Good news! I found a source for vacuum...the heater works now I found a plugged line on the attachment where the master cylinder hooks up. Connected there and presto . Still have to check the hoses for the tradratrac..but that's fine
Sent from my XT1650 using Tapatalk
I found a plugged line on the attachment where the master cylinder hooks up. Connected there and presto . Still have to check the hoses for the tradratrac..but that's fine Sent from my XT1650 using Tapatalk
2016 Jeep Patriot
"Faith"
"Faith"