Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
Ok, bought a new lift some months ago as part of a parts deal from a guy up in N. Ga. I thought the installation was going to be a no brainer, but I...
Last post
It's the '74-'75 years that are a problem with that 1 post or those years would have been sorted out a long time ago also.
Yes I have 82 j10 4.2 with the t-176 trans and I was wondering what I would need to switch from the 4.2 to a 360 I can get a 79 Cherokee cheap but I...
I'm trying to make a list of TFI parts here is what i have so far
wires
cap/rotor
is this the right one? i want to use the ford style cap...
Last post
Something I can add! I have the TFI coil conversion and the bigger cap on my rig. I did a tune up a couple months ago and bought the 460 wires and a...
Got a '69 gladiator J3000. Dana 44 front and Dana 53 rear (yes it exists). Disc conversions for the rear always seem to require a 6 lug hub for the...
Last post
I'm really not looking to lift the truck any more. The truck is an M715 body, so there is already plenty of clearance for oversized tires. As it sits...
Hey guys! So, my rig came with a Holley electric pump but not plumbed or wired up. How do you guys have yours? I heard it should be low and as close...
Last post
12v fused ign to oil pressure safety switch terminal NO , oil safety switch terminal C to fuel pump +, oil pressure safety switch terminal NC to...
Okay, got the parts Jeep home, put a battery in it and a little gas and it busted right off! Runs pretty darn good considering it's been sitting for...
I've been messing around with some steering box swaps lately and have run into the 3/4 vs. 11/16 input splines. I noticed they seem to be held on by...
Last post
That pin controls the flex pin inside the reed valves that control the amount of pressure applied when you turn the wheel. The harder the wheel is to...
Ok bear with me, This may be a case of way overthinking this and if someone has a better option I would love to hear it.
I have been thinking about...
Last post
The black cloth tab you see is connected to a lever that allows the seat back to fold forward, and releases the seat mechanism so that the whole seat...
Well i finally got the springover and shackel flip done on the old 79 and thought I would post a few pics. This just has a spring over, 36 swampers,...
So, I had developed a pretty bad bog upon initial tip in with the Cherokee. I pulled the carb off, looked it over and found I was getting little to...
Last post
Just wanted to let everyone know that the Jeep is running fantastic. The thing that made the biggest difference? Raising the float level between 1/32...
OK so I'm just finishing up a motor swap from a blown up and broken block 401 to a stock 360 and I have a problem with the vacuum fluttering or call...
Last post
An old time solution for a sticky valve or lifter (ticking) was to pour a quart of ATF in the engine oil and run it for a day or two before changing...
I know this subject has ben beat to death, but I have a question about a Wagoneer I found on Rough Country's web site. It says in the caption that...
Last post
Thanks. It was one of those I wish I woulda kept, but someone made an offer I couldn't refuse. It was also prett much show quality paint and interior...
Was the flywheel off? (didn't see it was stick) I had several AMC V8s flywheel bolts back out on me. I saw one guy lose his flywheel at the track in...
Hey everyone I'm new here with my new 1979 Jeep Cherokee chief widetrack. I brought the truck home and did some general work to it and am now having...
Last post
I started the truck today and it ran ok but still needed me to play with the gas to keep it alive for about a minute. I'm pretty sure my choke is a...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum