Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
I'm considering running the 37 military radial Goodyear tires on my J10 project. They are less than half what a comparable 37 runs price...
Last post
Trailworthy (just using them as an example) charges 155 for a recentered 8 bolt Hummer wheel. So that's 600 plus about 100-150 for shipping. You are...
The starter, battery, and alternator are all new.
I started her up Sunday w no problem. Let her run for 2 minutes but I'm sure that was not long...
Last post
Charged the battery 3 days ago. Ran it for 20 min. Went back today and she fired right up. Ran her for a half hour.
Just sold my crappy 2012 equinox...
I have a 77 j10 AMC 360 the previous owner installed an MSD distributor I was wondering if the stock coil is OK to use with this or if I should...
Last post
Tim I was wondering if I needed an msd coil to go with the distributor thank you both for the good info I will do some research and see if I can find...
Anyone know the specs of the front spring perches on an 88 grand wagon? Do they need to be the same width as the springs? Does length matter? Anyone...
Last post
Very slowly. Takes a good tailwind or a push to move it right now because my draglink isn't long enough to turn right very well yet. It sits pretty...
Was looking at the price differences between the 12.5's and 10.5's online. I'm curious if anyone with a pickup has run this size or if they look THAT...
Last post
I think you made my decision for me rocky. Thanks. I am regretting buying 31's initially now. Out of curiosity anyone else run them?
Would using the Dana 60 front axle from a 97 2500 be a decent candidate for axle swaps?
I know that they are coil sprung and that I would need to cut...
Hey all,
Is this the right gasket to use with an Edelbrock Performer intake on a 360? Some just have the gaskets on the ports, then there's this one...
Last post
X2 the gasket/valley pan metal->metal seal works very well, but note that it is a one time shot, you use it you loose it, so make sure you set your...
Anyone have any close up pictures of wagoneer rear fenders trimmed. I plan on cutting along the body line around the rear fender, think it's about 2...
Last post
No road salt around here but lots of rain and beaches
Hey guys, I am new to this forum, been trying to track down some information about a 727. I want to convert my 88 grand wagoneer to something easier,...
Last post
Hey guys, I am new to this forum, been trying to track down some information about a 727. I want to convert my 88 grand wagoneer to something easier,...
Hey guys So I have a 1989 Grand wagoneer with add a leafs all the way around, inch and a half lift of shackles up front and 2 in blocks behind... Ive...
Last post
My Wagoneer has had Monroe load-leveler coil-over style shocks on it since before some of your Grand Wagoneers were made. Never broken a shock mount,...
Pulled the front drivers seat out today and found that the front outside seat mount had rusted completely off. My Wag is an 86. Anyway to convert the...
Last post
I'm looking to do the same swap, I have had 0 luck finding bases
Hey looking to up grade my engine cam in my 81 cherokee 360 750 Holley carburetor Holley manifold auto transmission 727 with a/c ,,looking for a good...
Last post
That carb is waaaay to big for a 360 unless you are building a really high RPM engine. 600-650 is more than enough even for upper RPM with a mildly...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum