Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
I put a rebuilt motor in my Cherokee--broke it in correctly . I used the brake-in oil provided and ran it for half an hour with varying RPMs and then...
Last post
Have had 3 different good to new batteries, the old & new starters in the truck over last 2 years, and all acted the same way. Starts fine cold, an...
So in 76 the j10 didnt have cats or charcoal canisters etc. Mine still has no cats.
Was thinking of putting them on in the future. Reason is the...
Last post
Thinking to change where you buy your gas, and see if it makes a difference. Will take a couple tanks or so to notice, but todays gas blends are not...
Had changed all lights to leds replaced relays switches turns worked great haz worked also.
Starting it today she coughed hard stopped ,now have a...
Last post
This is a common symptom with bad grounds. Note the front hazards/indicators ground through the turn signal switch. Suggest you trace this out on the...
Hi, im new with my 83 Wagoneer, factory A/c.
First owner oberhold the engine and since than the a/c is not filled, bit should work, he said.
In want...
Last post
I wrote this on the duplicate thread.......
Truck should be running to check compressor clutch, but sure there is a test with a multi meter that...
Hi, im new with my 83 Wagoneer, factory A/c.
First owner oberhold the engine and since than the a/c is not filled, bit should work, he said.
In want...
Last post
Truck should be running to check compressor clutch, but sure there is a test with a multi meter that could be done. Before you start pumping the...
I am working on eliminating vapor leakage from my fuel system by adding a check valve and charcoal canister. This device (found on a CJ site)...
Last post
Likely Jeep used an unvented tank for the production part, and supplied the vented tank (which will work for both applications) as the service part....
Ok all, my saga continues with my AC. Everything has been replaced, held really good vacuum overnight, pressure tested system and sprayed soapy water...
Last post
Where us the broken thermistor located ? On the fan switch in cab ?
My 1978 Wagoneer 360 came with the stock 4barrel Motorcraft 4350. Several months ago, when dialing in the idle, I noticed the engine was unresponsive...
Last post
Would verify fuel flow is free of contaminants. Recently heard of some folks having issue with the Chinese made bypass filters, where the glue that...
Now that the engine stuff is pretty much done, I'm moving onto body and frame. Bed comes off next week update fuel system, brake & fuel lines and to...
Last post
Thanks for all of the replies and info. Just what I was looking for. By the way I should have been more specific in my post. My intention is to use a...
Have a 77 with the 360 and turbo 400. Have gone thru about a dozen flex plates in the last 25 years. Just changed out another and 3 weeks later it's...
Last post
Amazing! Thanks a bunch for the reply, looks like dowel pins are getting added to the list this time.
Found a mystery box in my 1984 J10, any help in identifying it would be appreciated.
Inside the cab, passenger side, taped just to the right of the...
Last post
i wonder why no one can get them working, i mean i tested the white box, the diaphram was good, i even replaced it with another from the jy that was...
My alternator squeaks because finding two belts the exact same length is almost impossible. I was farting around on the internet and stumbled across...
Last post
Spec sheet for the gates mentioned in Michel's post:
I price checked then and they are about $33 a piece both as the gates and NAPA versions....
Hi. Putting in a new fuel pump. 79 J10. Got the old one out pretty easily, popped right out. Is there a mystery to getting the new one in? I watched...
Last post
Crank the engine a split sec9nd to change the lob position.. put one bolt in the left hole and pull the pump down to move the lever and put the bolt...
I have a 1970 Wagoneer with the Buick 350/TH400. I'm getting a lot of mixed information looking at catalogs in terms of which transfer...
Last post
Sorry to keep bugging y'all. As I was installing the cross member and the transfer case mount nothing is lining up, ie: the entire cross member needs...
Doing an engine swap. Having fits with all the vacuum lines. Getting rid of some etc. I have one bad reverse TAC vacuum valve I am sure of. Anyone...
Last post
Greetings. In the grand scheme of things you can get away with:
1. Vacuum to the brakes
2. PCV valve (and crank case to air filter vent)
3. ported or...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
