'83 CJ 8 Scrambler
Posted: Fri Jan 25, 2019 2:34 pm
Well... Here it is folks. I promised myself I wouldn't sell it but I gotta shake something loose. Derf, if your interested, you have first dibs but I gotta make something happen soon.
Basics:
1983 CJ-8 Scrambler, Slate blue w/slate blue interior.
'83 AMC 360 from a low mile waggy.
NV4500 5 speed tranny
Northwest fabworks Blackbox crawl box
Dana 300 t-case
Waggy Dana 44 front with 4:10s and ARB locker and warm premium hubs
AMC 20 rear with Warn full float kit, 4:10s and Detroit locker.
BDS leaf springs in SOA configuration
35" BFG mud TAs with about 75-80% tread?
Parts Mike flat top arms and drilled knuckles for high steer
Seats are from a 200? Nissan Pathfinder. Ready to be wired for the heaters to work.
Good stuff: Runs and drives well (once I rebuild the carb).
Have full hard top, half cab w/bulkhead, and a full soft top.
Warn 8274 in modified TJ ARB bumper
Trucklite LED headlights
Stero has no headunit, uses Bluetooth from cell phone to signal amp which drives dash speakers and sub mounted in bulkhead.
Full size spare with matching wheel has never been on the ground.
Not-so-good:
Carb need rebuilt. Can't do it this weekend as I have Army stuff but should get it done soon.
Needs a front driveshaft and linkage for t-case to make 4wd function.
Front locker needs to be plumed for compressor.
Small amount of rust above rear wheelwells and where windshield frame meets body.
Need to install slider window in halfcab.
Full top needs a side window reinstalled.
Not sure if all the hardware is there for full soft top but it looks nearly new (still in the box)
I also have a laundry list of things that can go with the Jeep. Here's a short version:
On board air compressor. (New)
Replacement steel gas tank that's about 30 gallons?
HEI distributor and wires (new)
Edelbrock performer intake and carb (basically new. Was on a fSJ when engine broken in)
Hydraulic clutch conversion (new)
Steel tailhousing for NV4500 because the aluminum one leaks. Also have 6pints of the correct fluid (not cheap)
Who knows what else....
Pretty sure I have a back seat for it too.
Have a Howell TBI fuel injection kit I bought used. It is for a dodge 360 so will need a new computer chip.
We are trying to buy a house and we just don't bring ok n enough to make that happen. Need this to sell fast so if you ha e any questions, please ask. Shoot me a text or email if you prefer. I will tell you whatever I know, good or bad.
Looking for $13000.00 but cash (soon) talks.
Basics:
1983 CJ-8 Scrambler, Slate blue w/slate blue interior.
'83 AMC 360 from a low mile waggy.
NV4500 5 speed tranny
Northwest fabworks Blackbox crawl box
Dana 300 t-case
Waggy Dana 44 front with 4:10s and ARB locker and warm premium hubs
AMC 20 rear with Warn full float kit, 4:10s and Detroit locker.
BDS leaf springs in SOA configuration
35" BFG mud TAs with about 75-80% tread?
Parts Mike flat top arms and drilled knuckles for high steer
Seats are from a 200? Nissan Pathfinder. Ready to be wired for the heaters to work.
Good stuff: Runs and drives well (once I rebuild the carb).
Have full hard top, half cab w/bulkhead, and a full soft top.
Warn 8274 in modified TJ ARB bumper
Trucklite LED headlights
Stero has no headunit, uses Bluetooth from cell phone to signal amp which drives dash speakers and sub mounted in bulkhead.
Full size spare with matching wheel has never been on the ground.
Not-so-good:
Carb need rebuilt. Can't do it this weekend as I have Army stuff but should get it done soon.
Needs a front driveshaft and linkage for t-case to make 4wd function.
Front locker needs to be plumed for compressor.
Small amount of rust above rear wheelwells and where windshield frame meets body.
Need to install slider window in halfcab.
Full top needs a side window reinstalled.
Not sure if all the hardware is there for full soft top but it looks nearly new (still in the box)
I also have a laundry list of things that can go with the Jeep. Here's a short version:
On board air compressor. (New)
Replacement steel gas tank that's about 30 gallons?
HEI distributor and wires (new)
Edelbrock performer intake and carb (basically new. Was on a fSJ when engine broken in)
Hydraulic clutch conversion (new)
Steel tailhousing for NV4500 because the aluminum one leaks. Also have 6pints of the correct fluid (not cheap)
Who knows what else....
Pretty sure I have a back seat for it too.
Have a Howell TBI fuel injection kit I bought used. It is for a dodge 360 so will need a new computer chip.
We are trying to buy a house and we just don't bring ok n enough to make that happen. Need this to sell fast so if you ha e any questions, please ask. Shoot me a text or email if you prefer. I will tell you whatever I know, good or bad.
Looking for $13000.00 but cash (soon) talks.