Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
Well I managed to do some trading and got me a J truck thats pretty much exactly what I wanted to start with. Its a 258 t177 and np208 shortbed with the brow and AC. I need to find a razor grill and swap the bench for the buckets in my parts cherokee.
Things to do....
1.Rebuild carb
2. Hei distributor
3. Window lift bar drivers side
4. Fix rust in drivers floor pan
5. New hoses belts and fluids
6. New brake soft bits and hard bits as needed
7. Tailgate handle linkage repair or replace
8. Tires
9. Fix all the rust and paint (someday)
Last edited by Greenmachine on Sun Jan 17, 2021 3:32 pm, edited 1 time in total.
1975 Cherokee S factory 360,t-18, 4" hellcreek, slot mags 33" bfg's, performer intake, and Fitech fuel injection.
1980 J10 304, 5 spd, 4" Superlift, 4.88 Gears, 35" Maxxis Big Horns
1961 fc-150 fishing truck (on hold)
1980 Cherokee wrangled & mangled
MSD complete system
Eddy intake
Holley 650
Comp cam 270H
4" Rusty's
Ramsey 12K winch
208
Built to drive not sit in the garage.
No longer strangled. I didn't build it for anyone else.
If you can't improve it why waste your time?
Grip Spurs were THE TIRE in Montana until the swamper came out. Cenex/Farmers Co-op sold them and and most of my jeeps wore them. Great tire back in the day.
1977 Cherokee Chief - The Blair Jeep Project III
A collection of parts flying in close formation
I reaqlly wanted to get it running today as it was supposed to just need a carb rebuild (was told it leaked bad). I rebuilt the carb so thats one thing off my to do list...
Turns out it wasn't getting fire so I swapped in the module from my parts Cherokee. Then it wasn't getting fuel with the pump having a direct hose into a gas can so I replaced the fuel pump. Had to call it a day after that but it's still not pulling fuel out of the tank so I will have to start chasing lines. It needs some timing attention too as it backfired pretty spectacularly shooting the oil fill/vent cap into the hood and then into my face. It also blew the dip stick out. HEI should be here in a day or two and I will address the timing then. Hopefully I can get her running tomorrow....
1975 Cherokee S factory 360,t-18, 4" hellcreek, slot mags 33" bfg's, performer intake, and Fitech fuel injection.
1980 J10 304, 5 spd, 4" Superlift, 4.88 Gears, 35" Maxxis Big Horns
1961 fc-150 fishing truck (on hold)
You should check the oil for gasoline saturation ASAP!
Having the cap and dipstick pop out after a misfire says your oil is full of gas and you've got a piston ring allowing burning combustion gasses into the crank case. Bad scoobies!
1977 Cherokee Chief - The Blair Jeep Project III
A collection of parts flying in close formation
Probably a result of pouring gas down the carb trying to get it to hit. I would say it's a combination of fuel getting in the crankcase and the timing being off. Its not got enough in the oil that you can smell it on the dipstick.
1975 Cherokee S factory 360,t-18, 4" hellcreek, slot mags 33" bfg's, performer intake, and Fitech fuel injection.
1980 J10 304, 5 spd, 4" Superlift, 4.88 Gears, 35" Maxxis Big Horns
1961 fc-150 fishing truck (on hold)
Greenmachine wrote:Probably a result of pouring gas down the carb trying to get it to hit. I would say it's a combination of fuel getting in the crankcase and the timing being off. Its not got enough in the oil that you can smell it on the dipstick.
Gotcha!
Let us know how it goes.
1977 Cherokee Chief - The Blair Jeep Project III
A collection of parts flying in close formation
Well it is now purring like a kitten. I think it idles smoother than my 2006 LJ. Turns out the timing was fine. I thought at first it was the needle sticking as it would run for 20-30 seconds and die and would not start back. I figured it was burning through the float bowl and then fuel starving. It was also just squirting out of one port. Ended up taking it apart about three times and using the old accel pump to clear the venturi ports. Must of had something in it or i wasn't holding my mouth right... Works great now.
On a unrelated note I finished refinishing my slot mags and got my 33's mounted. 75 Cherokee S with 4" Hellcreek and 33's.
1975 Cherokee S factory 360,t-18, 4" hellcreek, slot mags 33" bfg's, performer intake, and Fitech fuel injection.
1980 J10 304, 5 spd, 4" Superlift, 4.88 Gears, 35" Maxxis Big Horns
1961 fc-150 fishing truck (on hold)
HEI in and running. I need to replace all the rubber lines on the entire truck in the fuel system. They are toast and fuel pump looses prime if it sits a couple days, and fuel leaks at the tank... I went with the $60 HEI off Amazon. It is probably crap but it looks pretty nice. I am surprised it can be made for $60 much less sold. I would have degreased the engine but it was in the single digits today and about a 30mph wind...
1975 Cherokee S factory 360,t-18, 4" hellcreek, slot mags 33" bfg's, performer intake, and Fitech fuel injection.
1980 J10 304, 5 spd, 4" Superlift, 4.88 Gears, 35" Maxxis Big Horns
1961 fc-150 fishing truck (on hold)
Well the 258 runs good and smooth and doesn't make any noise but it has some serious blowby.... The more I run it the worse it seems to get. I changed the oil and filter after I got it to run (it had oil in it and I have seen worse). I am now trying to decide what to do.. I really don't want to drop a grand or more on rebuilding. There is a 06 model 4.0 on cragslist right now with bent rods 40k miles was hydrolocked. Head is suppoed to be good for $150... Was contemplating stroker.... I also have a running 360 in my parts chero with a nib cam, intake, timing set, and polished holley 600 on the shelf. I could ebay for the money or put it in the 360 and swap it in... Or I could run it till it dies and then do something...
1975 Cherokee S factory 360,t-18, 4" hellcreek, slot mags 33" bfg's, performer intake, and Fitech fuel injection.
1980 J10 304, 5 spd, 4" Superlift, 4.88 Gears, 35" Maxxis Big Horns
1961 fc-150 fishing truck (on hold)
Put on some stock monroe shocks, my other set of slot mags and a set of kenda klever at's. Dropped the nasty tank to replace the hoses and sending unit and vent grommet.
Didn't remeber to take many pictures... Covered in nasty old gas and stinky fumes... Had to keep opening the door to let it air out and it was 19 degrees...
1975 Cherokee S factory 360,t-18, 4" hellcreek, slot mags 33" bfg's, performer intake, and Fitech fuel injection.
1980 J10 304, 5 spd, 4" Superlift, 4.88 Gears, 35" Maxxis Big Horns
1961 fc-150 fishing truck (on hold)
[quote="Greenmachine"]Well the 258 runs good and smooth and doesn't make any noise but it has some serious blowby.... The more I run it the worse it seems to get. [quote]