Whos making/selling the FSJ nerf bars / side steps
Posted: Tue Apr 03, 2018 7:05 am
Hey, there was a member building a nice set of nerf bars but I looked on both sites vendor listings and cant find them. Where did they go?
Full Size Jeep Network
https://www.fsjnetwork.com/forum/
Whos making/selling the FSJ nerf bars / side steps
Page 1 of 1
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Tue Apr 03, 2018 7:11 am
That's rstep (Bob) vendor-ing under the monacker "Evil Twin Fab".
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Tue Apr 03, 2018 2:52 pm
Thanks Matt. As Matt said I make them ,what questions you have?
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Tue Apr 03, 2018 5:16 pm
Some of the rock sliders.
Give you some idea of whats built.
Give you some idea of whats built.
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Thu Apr 05, 2018 6:56 am
Didnt you have a set with J10/J20 cut into the plate? What would a set for a long wheel base J10 cost and would it be cheaper to ship via Fasternal 3pl? Where are you located?
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Thu Apr 05, 2018 7:57 am
I am going to move this to General FSJ (Will leave a ghost topic behind), as its not a vendor listing. Which is the only thing that should be in vendors.
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Thu Apr 05, 2018 7:59 am
Thanks Stuka .I'll update my post in the venders section to include slides in the next week.
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Thu Apr 05, 2018 8:01 am
Rock,I'm located in Az. Yes I have cut J10 into the plates. can check fanenal for what their shipping is.
Pm sent.
Pm sent.
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Fri Apr 06, 2018 5:46 am
PM returned for one maybe two sets.
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Tue Oct 02, 2018 7:01 am
Are these still available?
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Sat Nov 06, 2021 7:43 pm
just got a set of these and not looking forward to lowering the tank again. I was thinking of weld studs to the frame to avoid this.
any expert advice on this? any concern with heat and poly tank? I doubt there is any real structural concern for the frame, but opinions wanted.
any expert advice on this? any concern with heat and poly tank? I doubt there is any real structural concern for the frame, but opinions wanted.
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Sun Nov 07, 2021 6:19 am
Fuel and brake lines would be my concern. Make sure to post pictures of the product when installed.
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Sun Nov 07, 2021 6:54 am
Fuel line is re-routed to the other side, with the addition of the Holley Sniper. Brake lines only.
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Sun Nov 07, 2021 10:41 pm
That is my green Cherokee that Bob posted above. I didn't have to lower my tank. Only problem I had was getting a short enough drill bit to drill between the body and frame. I wound up using a 90* adapter for my drill and shortened drill bit.ArchitectJS wrote: ↑Sat Nov 06, 2021 7:43 pm just got a set of these and not looking forward to lowering the tank again. I was thinking of weld studs to the frame to avoid this.
any expert advice on this? any concern with heat and poly tank? I doubt there is any real structural concern for the frame, but opinions wanted.
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Mon Nov 08, 2021 6:08 am
You don't have to drop the tank, just kinda scoot it to the side a few inches. At least that worked for me.
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Tue Nov 09, 2021 7:49 pm
Wish I had know this. I was being a dumbass and thought the frame was boxed all the way. Found out when gas came out the hole.
Luckily I found a company in town that could fix my tank. 2 months later and my garage still smells like gas
Re: Whos making/selling the FSJ nerf bars / side steps
Posted: Thu Nov 11, 2021 6:28 am
good tips, All. My Cherokee comes home from paint this weekend. I will start on layout then.Curly wrote: ↑Sun Nov 07, 2021 10:41 pmThat is my green Cherokee that Bob posted above. I didn't have to lower my tank. Only problem I had was getting a short enough drill bit to drill between the body and frame. I wound up using a 90* adapter for my drill and shortened drill bit.ArchitectJS wrote: ↑Sat Nov 06, 2021 7:43 pm just got a set of these and not looking forward to lowering the tank again. I was thinking of weld studs to the frame to avoid this.
any expert advice on this? any concern with heat and poly tank? I doubt there is any real structural concern for the frame, but opinions wanted.