Whos making/selling the FSJ nerf bars / side steps

Area for General FSJ related chat.
Post Reply

Topic author
rocklaurence
Vendor
Posts: 2564
Joined: Sat Mar 30, 2013 6:53 am

Whos making/selling the FSJ nerf bars / side steps

Post by rocklaurence »

Hey, there was a member building a nice set of nerf bars but I looked on both sites vendor listings and cant find them. Where did they go?
User avatar

REDONE
Posts: 2678
Joined: Tue Sep 13, 2011 5:48 pm
Location: Lakewood and Bailey, CO

Re: Whos making/selling the FSJ nerf bars / side steps

Post by REDONE »

That's rstep (Bob) vendor-ing under the monacker "Evil Twin Fab". ;)
79 J-10 (Honcho Mucho) KE0LSU
304/Performance Fuel Injection TBI/MTA1/SP2P/Magnum rockers
T18/D20/D44s&4.10s/33" Mud Claws
Grizzly Locker Rear
4" front spring drop, 5" rear shackle flip
Chevy style HEI (ECM controlled)
Dolphin "Shark" gauges in a fancy homemade oak bezel
3/4 resto, rotting faster than I've been fixing it.
User avatar

rstep
Moderator
Posts: 1237
Joined: Sun Dec 18, 2011 5:52 am
Location: Tucson,Desert
Contact:

Re: Whos making/selling the FSJ nerf bars / side steps

Post by rstep »

Thanks Matt. As Matt said I make them ,what questions you have?
1977 Cherokee Sold
I Don't own One
Stuff I Make.
http://fsjnetwork.com/forum/viewtopic.php?f=34&t=5620
User avatar

rstep
Moderator
Posts: 1237
Joined: Sun Dec 18, 2011 5:52 am
Location: Tucson,Desert
Contact:

Re: Whos making/selling the FSJ nerf bars / side steps

Post by rstep »

Some of the rock sliders.
Image
Image
Image
Image
Give you some idea of whats built.
1977 Cherokee Sold
I Don't own One
Stuff I Make.
http://fsjnetwork.com/forum/viewtopic.php?f=34&t=5620

Topic author
rocklaurence
Vendor
Posts: 2564
Joined: Sat Mar 30, 2013 6:53 am

Re: Whos making/selling the FSJ nerf bars / side steps

Post by rocklaurence »

Didnt you have a set with J10/J20 cut into the plate? What would a set for a long wheel base J10 cost and would it be cheaper to ship via Fasternal 3pl? Where are you located?
User avatar

Stuka
Site Admin
Posts: 11785
Joined: Thu May 12, 2011 5:53 pm
Location: CA
Contact:

Re: Whos making/selling the FSJ nerf bars / side steps

Post by Stuka »

I am going to move this to General FSJ (Will leave a ghost topic behind), as its not a vendor listing. Which is the only thing that should be in vendors.
2017 JKU Rubicon
Pevious Jeeps: 1981 J10, 1975 Cherokee, 2008 JK, 2005 KJ, 1989 XJ
User avatar

rstep
Moderator
Posts: 1237
Joined: Sun Dec 18, 2011 5:52 am
Location: Tucson,Desert
Contact:

Re: Whos making/selling the FSJ nerf bars / side steps

Post by rstep »

Thanks Stuka .I'll update my post in the venders section to include slides in the next week.
1977 Cherokee Sold
I Don't own One
Stuff I Make.
http://fsjnetwork.com/forum/viewtopic.php?f=34&t=5620
User avatar

rstep
Moderator
Posts: 1237
Joined: Sun Dec 18, 2011 5:52 am
Location: Tucson,Desert
Contact:

Re: Whos making/selling the FSJ nerf bars / side steps

Post by rstep »

Rock,I'm located in Az. Yes I have cut J10 into the plates. can check fanenal for what their shipping is.
Pm sent.
1977 Cherokee Sold
I Don't own One
Stuff I Make.
http://fsjnetwork.com/forum/viewtopic.php?f=34&t=5620

Topic author
rocklaurence
Vendor
Posts: 2564
Joined: Sat Mar 30, 2013 6:53 am

Re: Whos making/selling the FSJ nerf bars / side steps

Post by rocklaurence »

PM returned for one maybe two sets.

bburnz67
Posts: 1
Joined: Mon Oct 01, 2018 7:48 am

Re: Whos making/selling the FSJ nerf bars / side steps

Post by bburnz67 »

Are these still available?

ArchitectJS
Posts: 293
Joined: Thu Oct 15, 2015 5:01 pm

Re: Whos making/selling the FSJ nerf bars / side steps

Post by ArchitectJS »

just got a set of these and not looking forward to lowering the tank again. I was thinking of weld studs to the frame to avoid this.

any expert advice on this? any concern with heat and poly tank? I doubt there is any real structural concern for the frame, but opinions wanted.
1982 Cherokee, base (Bumppo)
AMC 258 / A727 - AMC 20 / NP208
Holley Sniper with Hyperspark
3" Rough County Lift

Topic author
rocklaurence
Vendor
Posts: 2564
Joined: Sat Mar 30, 2013 6:53 am

Re: Whos making/selling the FSJ nerf bars / side steps

Post by rocklaurence »

Fuel and brake lines would be my concern. Make sure to post pictures of the product when installed.

ArchitectJS
Posts: 293
Joined: Thu Oct 15, 2015 5:01 pm

Re: Whos making/selling the FSJ nerf bars / side steps

Post by ArchitectJS »

Fuel line is re-routed to the other side, with the addition of the Holley Sniper. Brake lines only.
1982 Cherokee, base (Bumppo)
AMC 258 / A727 - AMC 20 / NP208
Holley Sniper with Hyperspark
3" Rough County Lift
User avatar

Curly
Posts: 248
Joined: Fri Mar 13, 2015 11:31 pm
Location: Verde Valley, Az

Re: Whos making/selling the FSJ nerf bars / side steps

Post by Curly »

ArchitectJS wrote: Sat Nov 06, 2021 7:43 pm just got a set of these and not looking forward to lowering the tank again. I was thinking of weld studs to the frame to avoid this.

any expert advice on this? any concern with heat and poly tank? I doubt there is any real structural concern for the frame, but opinions wanted.
That is my green Cherokee that Bob posted above. I didn't have to lower my tank. Only problem I had was getting a short enough drill bit to drill between the body and frame. I wound up using a 90* adapter for my drill and shortened drill bit.
I start what I finish.

81 Wagoneer 4.2/auto
77 Cherokee S 360/Auto/QT
97 Jeep Wrangler

will e
Posts: 5094
Joined: Sat Aug 18, 2012 8:21 am

Re: Whos making/selling the FSJ nerf bars / side steps

Post by will e »

You don't have to drop the tank, just kinda scoot it to the side a few inches. At least that worked for me.
81 Waggy 'WILL E' Retired
82 Cherokee WT - SOA/SF/high steer/Alcan springs/agr box/Borgeson steering shaft/AMC 401/performer/holley TA/HEI/BeCool/727/ALTAS (2.0/2.72/5.44)/D60 Snofighter(Yukon Zip,hubs,stubs,4.56)/14 Bolt (FF,BF shave, Discs, ARB,Artec Truss)/MTR 37X12.5/Corbeau XRS Baja & 5 point retractable harness/Hella Aux lights/tuffy console/killer32 sliders/Evil Twin bumpers, rack and roll cage/WARN 8000/TT Fabworks steering brace/dual batts/custom TC skid plate/ARB fridge

fxtechphx
Posts: 90
Joined: Sat Jul 11, 2015 9:33 am
Location: Phoenix

Re: Whos making/selling the FSJ nerf bars / side steps

Post by fxtechphx »

will e wrote: Mon Nov 08, 2021 6:08 am You don't have to drop the tank, just kinda scoot it to the side a few inches. At least that worked for me.
Wish I had know this. I was being a dumbass and thought the frame was boxed all the way. Found out when gas came out the hole.
Luckily I found a company in town that could fix my tank. 2 months later and my garage still smells like gas
Tomorrow we may face destiny, we may fight and die and fall to the fires of perdition, but tonight is ours, and we drink and make merry.

ArchitectJS
Posts: 293
Joined: Thu Oct 15, 2015 5:01 pm

Re: Whos making/selling the FSJ nerf bars / side steps

Post by ArchitectJS »

Curly wrote: Sun Nov 07, 2021 10:41 pm
ArchitectJS wrote: Sat Nov 06, 2021 7:43 pm just got a set of these and not looking forward to lowering the tank again. I was thinking of weld studs to the frame to avoid this.

any expert advice on this? any concern with heat and poly tank? I doubt there is any real structural concern for the frame, but opinions wanted.
That is my green Cherokee that Bob posted above. I didn't have to lower my tank. Only problem I had was getting a short enough drill bit to drill between the body and frame. I wound up using a 90* adapter for my drill and shortened drill bit.
good tips, All. My Cherokee comes home from paint this weekend. I will start on layout then.
1982 Cherokee, base (Bumppo)
AMC 258 / A727 - AMC 20 / NP208
Holley Sniper with Hyperspark
3" Rough County Lift
Post Reply