1989 Project

J.Bradley · Post by **J.Bradley** » Wed Sep 16, 2015 3:07 pm

All Primed.

shimniok · Post by **shimniok** » Wed Sep 16, 2015 3:36 pm

pyro wrote:Define "donor"...looks a hell of a lot better than my pos

No kidding!!! I'd happily swap all my junk onto that 'donor' and run it!! Some guys have all the luck...

sent from my MotoX

NoLaFSJ · Post by **NoLaFSJ** » Thu Sep 17, 2015 12:49 pm

I think that one will work for me as well but we will have to compare. I need the under dash harness. I would also be interested in the engine harness as well if you don't need it. I'll pm you.

J.Bradley · Post by **J.Bradley** » Thu Sep 24, 2015 7:03 pm

Fresh paint, Just need clear put on now.

az chip · Post by **az chip** » Fri Sep 25, 2015 6:38 am

Who is doing the paint?

will e · Post by **will e** » Fri Sep 25, 2015 7:19 am

J.Bradley wrote:New wood and molding on fresh paint With some updated comforts and I would like a 2" lift to just clear some 31x10.50s. Mainly will be a grocery getter. To good of shape to make a trail rig.

They don't all have to be trail rigs. An option for a spring lift would be to get some custom springs made by Alcan. They can set them up for any type of lift/ride you are looking for.

With 31" and a couple of inches of lift it would still be a great rig to take down forest roads and get its feet dirty every once in a while.

J.Bradley · Post by **J.Bradley** » Sun Sep 27, 2015 10:17 am

It was painted at a friends shop. I know it is not the approved visqueen wrapped tarp barn method but we made do.

Thanks for the lift info and I am waiting to hear back from my email to Alcan. I am going to try the AAL for a few miles and see how they feel. If Alcan can get a soft ride I might go with them or get a factory set of springs and do a shackle reverse kit from Rock Laurence. I am not too concerned with having it at full flex so I would like it as low as possible while still clearing the 31X10.50.

J.Bradley · Post by **J.Bradley** » Mon Oct 05, 2015 9:07 pm

Finally got it somewhat back together.

Was told that it could not be a real Wagoneer resto without some visqueen so I set up the best I could.

J.Bradley · Post by **J.Bradley** » Wed Oct 14, 2015 10:04 pm

A little wet sanding on some highly cured clear coat

Guesstimating Trim

Almost There

Lumpskie · Post by **Lumpskie** » Thu Oct 15, 2015 1:54 pm

Wow, that looks good! Which wood grain did you go with?

J.Bradley · Post by **J.Bradley** » Thu Oct 15, 2015 4:44 pm

It is the TGW molding and Marine Teak

Windshield install Today

NoLaFSJ · Post by **NoLaFSJ** » Fri Oct 16, 2015 5:40 am

Wow, really looks good. Fine work!

J.Bradley · Post by **J.Bradley** » Thu Oct 22, 2015 1:53 pm

LightHouse

Jeep Below

Reflection

Empty Beach

Camping

Full Size Jeep Network

1989 Project

Re: 1989 Project

Re: RE: Re: 1989 Project

Re: 1989 Project

Re: 1989 Project

Re: 1989 Project

Re: 1989 Project

Re: 1989 Project

Re: 1989 Project

Re: 1989 Project

Re: 1989 Project

Re: 1989 Project

Re: 1989 Project

Re: 1989 Project