Vacuum Reservoir Tubing connector

Stock FSJ Tech Area
User avatar
89er
Posts: 45
Joined: Mon Aug 20, 2018 6:43 pm

Vacuum Reservoir Tubing connector

Postby 89er » Sun Sep 16, 2018 10:13 pm

Image

Does anyone know where can I find a replacement connector for this?
'89 Grand Wagoneer Baltic-blue/Tan

User avatar
will e
Posts: 3396
Joined: Sat Aug 18, 2012 8:21 am

Re: Vacuum Reservoir Tubing connector

Postby will e » Mon Sep 17, 2018 6:02 am

I think it is just a rubber tube. remove it and take it to the local parts store, they can match it up.
81 Wagoneer - 'WILL E' Retired

82 Cherokee WT - SOA/SF/high steer/Alcan springs/agr box/Borgeson steering shaft/AMC 401/performer/holley TA/HEI/BeCool/727/ALTAS (2.0/2.72/5.44)/D60 Snofighter(Yukon Zip,hubs,stubs,4.56)/14 Bolt (FF,BF shave, Discs, ARB,Artec Truss)/MTR 37X12.5/Corbeau Moab Seats/RCI 6point Harness/Hella Aux lights/tuffy console/killer32 sliders/custom bumpers and roll bar/WARN 8000/steering brace/CB/dual batts/custom TC skid plate

User avatar
fulsizjeep
Moderator
Posts: 4352
Joined: Sun Nov 06, 2011 7:21 am
Location: Mancos Valley, CO
Contact:

Re: Vacuum Reservoir Tubing connector

Postby fulsizjeep » Mon Sep 17, 2018 6:03 am

I would look in the Dorman section of most any auto parts store.
Sent from my IBM 5150 using TN5250 emulation.

Flint Boardman ~ http://jubileejeeps.org
Embracing the Borg Warner QuadraTrac since 1980 http://jubileejeeps.org/quadratrac
88 GW, 401/727/208, 5" lift, D44s/4.10s/locked up, 35s, a few Evil Twin mods, http://eviltwinfab.com and a few TT's Fabworks mods, http://www.ttsfabworks.com
76 401 Wag, 77 401 Wag, 77 401 J20

User avatar
89er
Posts: 45
Joined: Mon Aug 20, 2018 6:43 pm

Re: Vacuum Reservoir Tubing connector

Postby 89er » Mon Sep 17, 2018 6:25 am

Super glad it's that easy, thanks folks.

Any tips for getting to those 2 bolts out back there that hold the reservoir to the wall? I couldn't seem to get any socket or wrench in there and don't want to strip it with pliers or something.
'89 Grand Wagoneer Baltic-blue/Tan

User avatar
Stuka
Site Admin
Posts: 8681
Joined: Thu May 12, 2011 5:53 pm
Location: Sonora, CA
Contact:

Re: Vacuum Reservoir Tubing connector

Postby Stuka » Mon Sep 17, 2018 7:39 am

You should not need to remove the reservoir. That rubber piece should just slide off. It may take a bit of effort if the rubber has gotten hard. But it’s just vacuum line.
1981 J10 AMC 258 with HEI and Weber 32/36 DGEV Carb, T176, NP208, D44/M23 with 4.56 gears and Detroit Locker, 6" lift, 33x12.50 Cooper STT's, BJ's Offroad Rear Dozer Bumper.
2017 JKU Rubicon Lifted and stuff
Pevious Jeeps: 1975 Cherokee, 2008 JK, 2005 KJ, 1989 XJ

User avatar
89er
Posts: 45
Joined: Mon Aug 20, 2018 6:43 pm

Re: Vacuum Reservoir Tubing connector

Postby 89er » Mon Sep 17, 2018 7:51 am

Stuka wrote:You should not need to remove the reservoir. That rubber piece should just slide off. It may take a bit of effort if the rubber has gotten hard. But it’s just vacuum line.


Thanks for the reply. I have already purchased a new reservoir however, it was only 15 bucks and looked easy enough to access hah.
'89 Grand Wagoneer Baltic-blue/Tan


Return to “Stock FSJ Tech”

Who is online

Users browsing this forum: No registered users and 4 guests