Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
Im not sure whats going on with my 76 J10. I rebuilt the carb.. cleaned it really good.. ran good in warmer weather but in cold.. it wont start after...
Last post
Dont forget that these need the spacer between the intake and carb. They are notorious for the heat from the engine boiling out the fuel once theyre...
Hello from France,my name is nicolas,i have a 1982 J10 360 T177,and i have a clutch linkage problem,the previous owner had cut the pedal to bellcrank...
I have some questions that most likely have apparent answers, yet at risk of being exposed as a complete newbie (I am!) I thought I...
Last post
I got one wheel well glued in using 3M90. I’m putting the heater insulation throughout the back and hope it quiets the cab noise down. Gonna start on...
Hello from France,my name is nicolas,i have a 1982 J10 360 T177,and i have a clutch linkage problem,the previous owner had cut the pedal to bellcrank...
1974 J20. I bought my 74 J20 about 1 year ago. I developed a new gremlin that I can’t figure out. My right rear brake light and blinker bulb doesn’t...
Last post
Have you taken a multimeter to the wire itself to see if power is getting to that blinker wire first of all ?
I am in the process of stripping my 83 WT down to the frame. I wanted to see if anyone has used the following Eastwood products:
Rust Converter
Rust...
Last post
A p100 respirator from lowes for 35$ has charcoal in them you wont even smell it. Put a box fan on the ground or little fan with you to blow it away...
Hello - I am trying to locate some of those tiny screws that hold the center caps onto the wheels of the GW. Anyone know of where I might locate some...
Last post
I used 1/2 #8-32 stainless steel machine screws from my local hardware store. Same style Phillips head as the ones in the picture from TGW but the...
Evening All, I'm finally at the point where I need to make the decision to rebuild the engine in my 87 GW. Two plus years ago I fell down the rabbit...
Last post
if you are thinking about changing the lifters, check the lifter face that rides the cam, if it is dished time to consider the lifters and cam as it...
I finally got to test drive my 83 Cherokee with the new vent window assemblies I purchased from Jeep Recyclers.
I am getting alot of wind noise and a...
Last post
Thanks for the ideas. I will try the painters tape.
I was wondering if anyone knew where I could buy the intermediate parking brake cable for a 1977 Jeep Wagoneer? I’ve checked multiple stores and they...
Last post
J-truck cables won't fit a Wagoneer. Good of you to offer.
Hey all, I have a 1988 Grand Wagoneer I just bought, stack dana 44 the rear end is bad and I am having a hard time finding replacement 2.73 ring and...
Last post
Thanks for all the useful information gents!!! I saw that Chevy came out with a Dana 44 Gear set 2.73 is why I was asking.
Spent a couple of days over the past couple of weekends working on the Wagoneer. Was nearly impossible to start, and wanted to stall as soon as I put...
Last post
Most of the lines are 5/32 ID vacuum hose. The vacuum hose has no reinforcement but a thick wall so it will not collapse under vacuum. The washer...
Not devastated, ah, ah, that ornament is not a success in design... the bottom loop detached... lucky me while cranking, so no Tesla was scratched by...
Last post
I vote for the humping bears........ :mrgreen: 8-)
Working on the 82 Wagoneer, carb (2150) has been rebuilt, but still has starting/idle/drivability issues pointing to a worn carb body. I See a number...
Last post
The Chinesium Amazon carbs do not have the 2 stage power valve, or the provisions for it. I did luck out and find the piece of damaged choke linkage,...
Hi - I was hoping someone could kindly direct me to the Fog Lamp Relay in an ‘87 Grand Wagoneer. I’ve replaced both bulbs and the fog lamps are still...
Does anyone know if one could swap out the emergency drive diaphragm and indicator switch on top of the transfer case (BW 1339) while installed or do...
Last post
Got it, thank you . On vaca and will troubleshoot after nov 6.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
